This guide is here to assist users in trying to make the switch from the "old" Clover with AptioMemoryFixes to the new one with Open Runtime and Quirks (make sure to update Clover Configurator to the latest version as well). When updating to the latest revision of Clover, there are several obstacles one might face along the way. Since r5126 these are now obsolete and no longer supported, so an upgrade to r5126 or later is mandatory in order to be able to install and boot macOS Big Sur and Monterey with Clover!Īim: This guide is for everyone trying to update to the latest revision of Clover, so they can install and run Big Sur and newer on their machines. Guide is applicable to: Clover r5123 to r5143+ (UEFI only)īackground: Since the Pre-Release of Clover r5123, OpenCore's Memory Fixes have been integrated completely into Clover in the form of OpenRuntime.efi, replacing the previously used AptioMemoryFixes. I've uploaded accurate screen shots of my EFI and current ist minus SMBIOS I wondering if Rehabman meant G2,G3,G4? Because when I did disable them I got a not boot situation. G3 G4's when I disabled them would not boot. There are tons of battery patches there as well and a few others. That was the culprit plus I had to turn off the patches in ACPI for GFX to IGPU and BOD to HDAU and HDAS to HDEF so that APPLEALC and Whatevergeen could do their patching. In the SSDT's section there is an SSDT-IGPU.aml it is turned off from loading int Sorted Order it was causing Whatevergreen.kext conflicts and could not boot into get Console. This HP is rather new thing for me and I do not want to mess it up.Īnd a different animal and quite a relief actually from the old Asus. Had to go back to the site I had gotten the project from and ask questions but bits and pieces and sketchy because this is 450 G2 not many have this one. Everything works thanks to Rehabman's work. This is my first good working hack, the Asus had all kinds of issues I could not get straight because it was scarce and HD3000 isn't the greatest. I would greatly appreciate your diagnosis again. So I am wondering if it is necessary regardless of others machines. I know that I had to use OcQuirks.efi to get Catalina to boot and take the Quirks in Catalina and it works I have no problems. Had to reinstall Catalina.Ĥ> I am not aware of all the ins and outs as I got sketchy profiles from others. On the third reboot prior to getting to console to finish the install is when the message came about: SMC is no longer necessary or used in this system then it shutdown and that was the end of that. #>What I ran into while trying to install Big Sur on the third reboot was the message SMC is not used any longer then it shutdown the third time.ģ> I would assume to remove all the kexts as you mentioned but what I did was turned them off in Clover boot menu each time before during the install process which rebooted 3 three times. One of things on the list of things to do. I switched back to FakeSMC due to the sensors not working with VirtualSMC. Never had an issue I put in because at the Rehabman's Project page several were suggesting to install. I have looked at their ist it is to me a not needed thing I've seen where others are using NoTouchID.kext in Catalina and Big Sur. I was unaware of unsupported SATA and XHCI kext were no longer necessary as this was from Rehabman's project and everything worked with a few corrections. The screen shot is misleading if you look it is two different shots overlaid. Have two mouse drivers as it was acting up on install where the touchpad would flake then I put in the USBmouse. The EFI to see which ones I would require. This was originally Rehabman's Project for HP Probook for Mojave that put all these kexts into /L/E I just removed them and placed them in I took them off to have just the basics to upgrade.Ģ> I had pulled the /L/E kexts into EFI to test which ones' are needed I have deleted the Broadcom kexts a while back that was an inaccurate screen shot, I had just pulled them out of /L/E. I am performing upgrade as I do not have anything else loaded nor installed. Thank you for your diagnosis! Great Thanks! Greatly appreciate your insight and expertise!ġ> I am not doing fresh install wipe drive. Lilu, virtualsmc and whatevergreen as kexts. Start with the most minimal config possible: APFSDriverLoader, HFSPlus and Openruntime for drivers NoTouchID is no longer required for Catalina and onwardĪre SATA unsupported and XHCI unsupported are really necessary? Why are you using both BrcmPatchRAM2 AND BrcmNonPatchRAM2… it makes no senseīrcmFirmwareRepo cannot be injected through a bootloader, it has to be installed to S/L/E.
0 Comments
Leave a Reply. |